ATTO Technology Diamond Storage Array V-Class Instrukcje Operacyjne Strona 19
- Strona / 117
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
8
Components
which allows a connection
for setup, monitoring and
upgrade of the unit from
any computer system with
an RS-232 interface. The
optional 10/100 BaseT
Ethernet management
services card enables
Telnet-based monitoring
and management. It also
provides the ability to
update the firmware in the
array via FTP. LEDs
farthest to the left indicate
fault, unit ready, Host
Interface cards A and B
installation status, and the
power status for each
power supply.
To the right of the system
management card are
individual disk drive sleds
which also have LED
indicators for each drive’s
status. Each sled contains two hard drives. Up to
24 hard drives may be installed on the 12 sleds.
Empty bays should be covered by blank
faceplates or filled with empty sleds to promote
effective cooling. Access is provided by
loosening two screws and pulling on the sled
handle.
In the rear of the unit are the blower assemblies
which support hard drive, cabinet and power
supply cooling. Correct operation is displayed by
a LED at the top of each panel. The blowers are
held in place by removable screws.
The power supplies for the array are accessible by
loosening two screws and pulling on the power
supply module handle. The power standby on/off
switch is at the top of each module. A yellow LED
indicates
caution
and a green LED indicates
on
.
The power cord socket is at the bottom of each
power supply.
Between the power supplies and blower
assemblies are two slots that hold the Host
Interface cards. The HIC is the connection point
into the array and is available in 2-Gigabit Fibre
Channel, or Ultra 160 SCSI. Host Interface cards
have
fault
and
on-line
or
fault
and
activity
LED
indicators, depending on the model.
SCSI
The SCSI card faceplate has a rotary
binary-coded hex switch which allows you to set
the SCSI ID of the array. The SCSI card also has
an in channel, to connect by a cable to the unit’s
communication source, and an out channel,
available for daisy-chaining arrays together or to
complete termination using an external LVD
terminator.
Intelligent midplane (internal)
Disk drive sleds (12)
System Management Card
Power supplies
Host interface cards
Blower assemblies
- Diamond Storage Array 1
- Contents 2
- Disclaimer 10
- 1.0 Product Overview 12
- Fibre Channel model 13
- SCSI model 13
- 2.0 Technical Overview 14
- ADXT Powers ATA to New Levels 15
- CAUTIONCAUTION 16
- Quick start 17
- 3.1 Components 18
- Disk drive sleds (12) 19
- System Management Card 19
- 3.2 Physical Setup 20
- 2 Gb HIC uses 22
- 2 SFPs to connect up 22
- Fibre Channel connections 23
- SCSI connections 25
- Updating Firmware 26
- Drive, sled numbering 27
- RAID Level 0 27
- 4.0 Accessing the Array 28
- In-band CLI 31
- 4.2 Serial Port Access 32
- Serial port access 33
- Ethernet protocols 35
- Accessing the Array 36
- Information 37
- 4.4.1 ExpressNAV Pages 38
- Command Line Interface 41
- Diamond Storage Array 44
- 4.5.2 General Use Commands 45
- 4.5.5 Ethernet Commands 50
- 4.5.6 Diagnostic Commands 52
- 53
- Default: 4 55
- 5.0 Configuring Drives 60
- Interleave 61
- Partitions 61
- Hot Spare sleds 61
- Enhancing performance 61
- 5.1 JBOD 62
- 24 physical drives 64
- RAID 0 subsystem example: 64
- 4 Virtual Drives 64
- 6 Virtual Drives 67
- RAID Level 5 69
- Removing RAID groups 71
- QuickRAID10 1 = LUN 1 73
- QuickRAID10 2 = LUN 1 73
- QuickRAID10 3 = LUN 1 73
- You must use a 75
- SaveConfiguration Restart 75
- 5.7 RAID Interleave 76
- RAID interleave 77
- To merge partitions 79
- 5.9 Creating Zones 80
- Other operations 83
- RestoreConfiguration default 83
- 6.0 Copying Drives 84
- Copy drives 85
- 7.0 Updating Firmware 86
- Read/Writes 89
- Diagnostic 90
- Commands 90
- Warranty 90
- Monitors, reports 91
- 8.1 Troubleshooting 92
- 8.2 Resetting Defaults 94
- Reset defaults 95
- 9.0 Hardware Maintenance 96
- Disk Drives 98
- 9.2 Optional Hot Spare Sled 100
- LUN 1 LUN 2 101
- Glossary 102
- ATTO Technology Inc 104
- Driveinfo 105
- 106
- PartitionInfo 109
- ZoneInfo 110
- Symmetric Model 111
- Asymmetric Model 112
- Appendix D Product Safety 114
- Appendix E Specifications 115
- Appendix F Part numbers 116
- Appendix G Warranty 117
Powiązane produkty i podręczniki dla Macierze dyskowe ATTO Technology Diamond Storage Array V-Class
(26 strony)Hangar-9 1/4 Scale PA-18 Super Cub PNP manuály
Uživatelské manuály a uživatelské příručky pro Váhy Hangar-9 1/4 Scale PA-18 Super Cub PNP.
Poskytujeme 1 manuály pdf Hangar-9 1/4 Scale PA-18 Super Cub PNP ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji